Hi Steffan / twotower61

Changing the frequency is adjustable within practical limits by altering either the cap or the
resistor in the CR circuit which give you the "long" time period to changeover. In diagram
here it is 0.1uF and 2.4 Meg Ohm connected to pin 2 of op amp U1B.

Yes you will need three terminals on the socket ; one terminal (Normally Closed) to be
switched Open when inserting the plug.

Thanks for the site for voltage increaser. will look at it later. But ... Bob Beck stopped using
the higher voltage. he changed from 4x9 to 3x9 batts and settled for that. there is probably a
good reason for that. think skin burns :-).

OK, Tony

On 6 Nov 2007 at 18:50, twotower61 wrote about :
Subject : [microelectricitygermkiller2] Re: b

> Hi Baby_Grand -
>
> Could you please elaborate on how to change the frequency in the blood
> electrifier. I notice that some commercial models have different
> frequency settings. Perhaps one needs to use a different IC chip?
>
> If the bicolor LED is to be used to test the device, how does one turn
> it off during normal operation? Perhaps the phone jack that I got from
> the electronics supply which only has two solder points is the
> incorrect one? That part of the schematic (numbers 2 and 3 on the
> electrifier output jack) have me mystified!
>
> You mention using a fourth battery. Does this change the output to -36
> and +36 volts, or does the output voltage stay the same? Is the output
> voltage in the circuit regulated by the zener diodes or do they simply
> allow the LED to pulse red/green as the polarity changes? The circuit
> diagram shows the zener diodes opposed to each other.
>
> I plan to build a voltage amplifier that will amplify the voltage from
> a single 9V battery to 34V and add it to the front of the blood
> electrifier circuit. http://www.geofex.com/ circuits/+9_to_33.htm -
> I'm guessing since it is OK to add a fourth battery to the power
> supply, that running the blood electrifier on 34V will work
> satisfactorily.
>
> Thanks Much!
>
> --- In microelectricitygermkiller2@yahoogroups.com, "baby_grand"
> <bobluhrs@...> wrote: > > you should be able to feel the current
> pulsating (it's one of the > problems). the LED is to be used to
> test, not to run with, or it eats > a lot of current. If you have 3
> batteries, add a fourth one. I like > to put a .1mfd non-polar or
> ceramic capacitor across the output leads > to dampen the spike, but
> that is not "pure Beck" so you may not want > it. I like the Beck
> devices but set them to 1/60 hertz or one change > of current every 30
> seconds, that works best for me. > > :) > bG > > --- In
> microelectricitygermkiller2@yahoogroups.com, "maujm07" > <maujm07@>
> wrote: > > > > Hi guys! I just recently joined the group. I just want
> to ask if you > > could help about my beck device which was built by
> my brother last > > month. The problem is the bi-colour led did not
> flash from green to > > red. It only flashes on green. Beck stated it
> should flash alternately > > which indicates a reverse polarity. My
> brother already check the > > device with a tester and said its output
> is an AC current. I ask > > Carole from Sharing Health and told me
> that the led bi-colour that I > > bought could be different. She also
> told me that I can use the device > > coz the current is already AC.
> Please give me some advice. Thanks in > > advance. > > > > Mau > >
> From the Philippines > > >
>
>
>
>
>
> Yahoo! Groups Links
>
>
>